新品100W v1_激光电源_核心器件_

商品描述：br /> 　　本电源采用零电流半桥软开关电路，使电源具有效率高，响应速度快的特点，很容易配合各种厂家的激光管。端口控制简单，适应高低电平两种信号，利用TTL电平即可控制激光的启、停，同时加有异常保护开关检测外部是否通水、通风等。
　　激光功率调节既可以输入0到5V的模拟信号，也可以输入PWM信号用以控制激光功率的大小。
　　电源具有开路保护功能：在保护接地良好的情况下，电源可以短时间工作于开路状态，这样可以避免因激光管爆裂造成激光电源的损坏。
出厂老化试验:
　　每台电源都会经过满载状态下高温60度12小时老化试验,7秒钟开停电源试验500次。
主要技术参数：

交流输入电压		AC220V 或 AC110V
直流输入电压		DC300V 或 DC150V
交流输入频率		47～440Hz
最大电压输出		50KV
最大电流		38mA(视不同厂家的激光管)
效率		91%
过流保护		最大电流的130%
开路保护		有（短时间）
结构		风机冷却
高电平控制电压范围		≥3V
低电平控制电压范围		≤0.8V
工作温度		-30℃～+65℃
相对湿度		20～85%RH（不结露）
耐压	输入—输出	AC1500V1分钟≤10mA
	输入—壳	AC1500V1分钟≤10mA
	输出—壳	连接
绝缘电阻		≥50MΩ（DC500V）
对地泄漏电流		≤1mA（AC220V）≤0.5 mA（AC110V）
抗振性		振幅0.5mm频率10～55Hz3维方向2小时
无故障时间MTBF		≥30,000hours
满载60℃高温试验时间		12 hours
7秒开停电源试验		500次
最大尺寸（长宽高）		350mm220mm95mm

The power supply adopts zero-current half-bridge soft switching circuit, featuring high efficiency, fast response and easy matching for laser tubes produced by various manufacturers. Its ports can be controlled simply to adapt to high and low level signals; the switch of the laser can be controlled by TTL electrical level. Meanwhile, it has an additional abnormal protection switch to test external water supply, ventilation, etc.
The laser power can be adjusted by entering either 0 to 5V analog signals or PWM signals.
The power supply has open circuit protection function: under the well-grounding circumstances, it can work under open circuit state within short term to avoid laser power supply damages caused by laser tube burst.
Ex-factory Aging Test:
Each power supply should go through 12-hour, 60℃ high temperature aging test under full load with 500 times power supply switch in 7 seconds.
Main Technical Parameters:#p#分页标题#e#

AC Input Voltage		AC220V or AC110V
DC Input Voltage		DC300V or DC150V
AC Input Frequency		47~440Hz
Voltage Output		50KV
Maximum Current		38mA (depending on the laser tubes of different manufacturers)
Efficiency		91%
Overcurrent Protection		130% of maximum current
Open Circuit Protection		Yes(short term)
Structure		Fan cooling
High Electric Level Control Voltage Range		≥3V
Low Electric Level Control Voltage Range		≤0.8V
Working Temperature		-30℃~+65℃
Relative Humidity		20~85%RH(no condensation)
Voltage Resistance	Input—Output	AC1500V1minutes≤10mA
	Input—Shell	AC1500V1 minutes≤10mA
	Output—Shell	Connection
Insulation Resistance		≥50MΩ(DC500V)
Earth Leakage Current		≤1mA(AC220V)≤0.5 mA(AC110V)
Vibration Resistance		Amplitude: 0.5mm frequency 10~55Hz 3D direction 2 hours
MTBF		≥30,000hours
Test Time at Full Load and 60℃		12 hours
Power Supply Switch Test within 7 Seconds		500 times
Maximum Dimensions (LWH)		350mm220mm95mm

#p#分页标题#e#

转载请注明出处。

• 亮点光电推出全国产化光纤陀螺用ASE激光光源	• 新型纳米晶体管可在高电压下保持低温实现高效
• 电控系统是半导体激光器成败的关键	• 光纤激光器主控板及红光驱动
• 4-6路连续光纤激光器集成驱动模块	• CO2激光电源图-宏源激光电源接线说明
• 半导体锡焊激光系统塑料焊激光系统LDS200	• CO2激光电源怎么修？
• 半导体锡焊激光系统塑料焊激光系统LDS200	• CO2激光电源故障怎么修？